absolute maximum ratings (4) 1) typical value at nominal input voltage and full load. 2) tested by nominal vin and constant resistor load. 3) measured input reflected ripple current with a simulated source inductance of 12uh. 4) exceeding the absolute ratings of the unit could cause damage. it is not allowed for continuous operating. the models listed are just for standard type. if you need a special specification product, please contact our service. phone: +49 69 984047-0, mail to: info@rsg-electronic.de or use the forms on www.rsg-electronic.de (?kontakt). dip24, w ide 2:1 input range full smd technology 1500 vdc isolation up to 3500 vdc isolation continuous short circuit protection efficiency up to 82% -40c~85c operation temperature range optional plastic case input specifications efficiency (typ.) see table i/o isolation voltage (3 sec.) input/output 1500~3500 vdc metal case / input & output 1000 vdc i/o isolation capacitance 470 pf typ. i/o isolation resistance 1000 m ohm switching frequency typ. 266 khz humidity 95% rel. h reliability calculated mtbf (mil-hdbk-217f) > 1.121 mhrs. safety standard (designed to meet) iec 60950-1 general specifications case material nickel-coated copper non-conductive black plastic (ul94v-0 rated) base material non-conductive black plastic (ul94v-0 rated) pin material ? 0.5 mm brass solder-coated potting material epoxy (ul94v-0 rated) weight metal 17.0 g, plastic 13.5 g dimensions 1.25 x 0.8 x 0.4 operating temperature (see derating curve) -40c~ 85c maximum case temperature 100c storage temperature -40c~125c cooling nature convection note these are stress ratings. exposure of devices to any of these conditions may adversely affect long-term reliability. input voltage (100 ms) 12 modes -0.7 ~ 24 vdc 24 modes -0.7 ~ 40 vdc 48 modes -0.7 ~ 80 vdc lead soldering temperature 260c (1.5 mm from case 10 sec.) all specifications typical at ta = 25c, nominal input voltage and full load unless otherwise specified. the information and specifications contained in this data sheet are believed to be correct at time of publication. however, we accept no responsibility for consequences arising from printing errors or inaccuracies. subject to change without notice. page: 1/3 last update: 21.07.09 voltage accuracy 1% line regulation 0.5% load regulation 0.5% (output 3.3v model / 3.3v model) 1.5% ripple & noise (20 mhz bandwith) (1) 60 mv pk-pk short circuit protection indefinite (automatic recovery) temperature coefficient 0.02%/c capacitor load (2) see table voltage range see table max. input current see table no-load input current see table input filter pi type input reflected ripple current (3) 35 ma pk-pk environment specifications rr3-s03/d03 3 watt 2:1 regulated single & dual output output specifications physical specifications
rr3-s03/d03 3 watt 2:1 regulated single & dual output model selection guide page: 2/3 last update: 21.07.09 name/package rr3=dil24 add suffix p at the end for plastic case! derating curve number structure isolation 1=1.5kvdc 3=3.5kvdc power 03=3w code internal rr3 - xx xx s/d 03 a x (p)* type s=single d=dual output 03=3.3v 05=5v 09=9v 12=12v 15=15v 24=24v input 12=9~18v 24=18~36v 48=36~72v model number input input current (ma) output output current efficiency capacitor range vdc no load / full load vdc full load (ma) @fl (%) load ( hf) rr3-1203s03ax 9-18 22 / 343 3.3 900 72 470 rr3-1205s03ax 9-18 22 / 328 5 600 76 470 rr3-1209s03ax 9-18 22 / 320 9 333 78 68 rr3-1212s03ax 9-18 22 / 312 12 250 80 47 RR3-1215S03AX 9-18 22 / 312 15 200 80 47 rr3-1224s03ax 9-18 22 / 313 24 125 80 22 rr3-1203d03ax 9-18 22 / 343 3.3 450 72 220 rr3-1205d03ax 9-18 22 / 328 5 300 76 220 rr3-1209d03ax 9-18 22 / 312 9 167 80 33 rr3-1212d03ax 9-18 22 / 312 12 125 80 22 rr3-1215d03ax 9-18 22 / 312 15 100 80 22 rr3-1224d03ax 9-18 22 / 313 24 63 80 10 rr3-2403s03ax 18-36 12 / 171 3.3 900 72 470 rr3-2405s03ax 18-36 12 / 164 5 600 76 470 rr3-2409s03ax 18-36 12 / 160 9 333 78 68 rr3-2412s03ax 18-36 12 / 156 12 250 80 47 rr3-2415s03ax 18-36 12 / 152 15 200 82 47 rr3-2424s03ax 18-36 12 / 153 24 125 82 22 rr3-2403d03ax 18-36 12 / 171 3.3 450 72 220 rr3-2405d03ax 18-36 12 / 160 5 300 78 220 rr3-2409d03ax 18-36 12 / 156 9 167 80 33 rr3-2412d03ax 18-36 12 / 152 12 125 82 22 rr3-2415d03ax 18-36 12 / 152 15 100 82 22 rr3-2424d03ax 18-36 12 / 153 24 63 82 10 rr3-4803s03ax 36-72 8 / 86 3.3 900 72 470 rr3-4805s03ax 36-72 8 / 82 5 600 76 470 rr3-4809s03ax 36-72 8 / 80 9 333 78 68 rr3-4812s03ax 36-72 8 / 78 12 250 80 47 rr3-4815s03ax 36-72 8 / 78 15 200 80 47 rr3-4824s03ax 36-72 8 / 78 24 125 80 22 rr3-4803d03ax 36-72 8 / 86 3.3 450 72 220 rr3-4805d03ax 36-72 8 / 82 5 300 76 220 rr3-4809d03ax 36-72 8 / 80 9 167 78 33 rr3-4812d03ax 36-72 8 / 78 12 125 80 22 rr3-4815d03ax 36-72 8 / 78 15 100 80 22 rr3-4824d03ax 36-72 8 / 78 24 63 80 10
mechanical specifications rr3-s03/d03 3 watt 2:1 regulated single & dual output page: 3/3 last update: 21.07.09 mail: info@rsg-electronic.de www.rsg-electronic.de rsg electronic components gmbh sprendlinger landstr. 115 d-63069 offenbach tel. +49 69 984047-0 fax +49 69 984047-77 efficiency vs output current 12 12 models efficiency vs output current 24 24 models efficiency vs output current 48 48 models rr3-xxxxx03a1 rsg 24 pin dil package nickel coated copper all dimensions are typical in millimeters (inches). 1) pin diameter: 1.0 0.05 (0.02 0.002) 2) pin pitch tolerance: 0.35 ( 0.014) 3) case tolerance: 0.5 ( 0.02) mechanical specifications 24 pin dil package plastic case (optional) pin nr. 1 2 3 9 10 11 12 13 14 15 16 22 23 24 dual +v input -v output common n.p. common +v output -v input -v input +v output common n.p. common -v output +v input single +v input n.c. n.c. n.p. -v output +v output -v input -v input +v output -v output n.p. n.c. n.c. +v input dual-3 n.p. -v input -v input common n.p. -v output n.p. n.p. +v output n.p. common +v input +v input n.p. single-3 n.p. -v input -v input n.p. n.p. n.c. n.p. n.p. +v output n.p. -v output +v input +v input n.p. pin connections rr3-xxxxx03a1p rsg all dimensions are typical in millimeters (inches). 1) pin diameter: 1.0 0.05 (0.02 0.002) 2) pin pitch tolerance: 0.35 ( 0.014) 3) case tolerance: 0.5 ( 0.02)
|
